A new wood-burning fireplace, installed in Miami Springs
Wood-burning fireplace installation for homes in Miami Springs, with the maker's instructions followed from rough framing onward.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What starts a fireplace installation project in Miami Springs
- Rusted metal inside an old fireplace
- A blank wall where a fire belongs
- A fireplace that cannot be repaired safely
- Framing too close to the old unit
Jump to
Installation decisions for a wood fireplace in Miami Springs
Choosing where the fireplace sits in the room
Location affects how a wood fire behaves. Installation manuals warn against spots with heavy air movement, such as beside a door people use often or near a return for the air conditioning. Drafts across the opening can pull smoke into the room instead of up the chimney.
Walk us through the furniture plan and the doors you use. We look at the wall you prefer and at one or two alternatives. If your first choice fights the airflow in the house, we say so and explain what the difference means for everyday use.
Standoffs and the header above the unit
Many factory-built units have standoffs on top that set the gap to the header and framing above. The header must sit where the manual shows, often resting on those standoffs rather than lower. Moving it down to suit a finish plan can close an air space the listing depends on.
We set the header height from the manual and check the standoffs before framing continues upward. If your finish design calls for a lower opening line, we explain what the listing allows. Any change is discussed before it is built, not corrected afterward.
Alarms and an extinguisher near the new fireplace
Manuals for wood fireplaces recommend a smoke alarm on each floor of the home and a fire extinguisher near the fireplace. They also recommend a household plan with more than one way out. These steps cost little next to the protection they add.
We mention these at handover because a new fireplace changes the room. Keep alarms for smoke and carbon monoxide working, and test them as their makers direct. None of this replaces the manual, which remains your reference for safe use.
Checks made before walls and ceilings close
Once drywall and ceilings are up, clearances, firestops and the attic shield disappear from view. That is why they are checked before the surfaces close. The manual's checklist and any required inspection happen at this stage, not after the finish.
We walk you through the open framing if you want to see what the finished wall will hide. Any item that needs correcting is fixed before closing. The confirmation goes into the written record, so the hidden work is documented. Ask questions then, since the answers are easiest to show with the framing open.
The fireplace installation scope, item by item
- Masonry fireplace footing and firebox plan
- Firestops and attic insulation shield
- Firebrick, baffle and refractory placement
- Daily cover for the open roof penetration
What people ask about wood fireplace installation
Should I pick the fireplace model before your visit?
It is better to wait. The inspection shows what the framing, attic and roof allow, and some models will not suit them. We can compare a few candidates with you afterward, so the unit you buy fits the installation it needs.
Do you set the tile or stone around the opening?
Only if the estimate names it. Often the finish belongs to a tile setter or mason. Either way, we mark the noncombustible zones and the mantel limit so whoever sets the finish works to the manual.
Where should furniture sit relative to the new fireplace?
Outside the clear space the manual prints for your model. Curtains, chairs and stored items stay back, and nothing combustible sits on the hearth extension. We point out the zone at handover so you can arrange the room.
More Ways to Care for Your Fireplace
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo