A gas fireplace for Coral Ridge, planned and installed
We plan the model, the vent route and the enclosure together before any appliance is ordered.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Projects that start with a gas fireplace plan
- A renovation opening up the wall
- No manual for the existing unit
- Controls you would like to update
- Moving the fireplace to a different wall
Jump to
Gas appliance, vent and enclosure as one plan
Vent tables decide the route
Every direct-vent gas fireplace manual includes vent tables. They set how far the vent may rise and run, how many elbows it may use and where it may end. Diagonal runs count toward both the vertical and the horizontal limits.
We draw the planned route against those tables before framing starts. If it fits, the route is recorded for the builder. If it does not, we look for a different path or position rather than stretching the rules. A route outside the tables can affect how the appliance lights and burns.
Elbows, offsets and the length of the run
Each elbow in a vent run adds resistance, and manuals count elbows and offsets against the allowed length. Some manuals let a pair of angled elbows replace a single square turn, and they explain how to measure pipe by its effective length rather than its overall length.
We keep the route as simple as the room allows and count every fitting against the table. If an offset is needed to clear a beam or duct, we check its effect before framing around it. The final route and fittings list are written into the installation record.
Fronts and trim from the maker's list
Decorative fronts, surrounds and trim kits are offered for specific models, and manuals allow only the kits the manufacturer supplies. Some fronts also carry the air openings the unit needs, so their design is not only cosmetic.
We order the front or trim from the list for your model and fit it as shown. If you prefer a look the maker does not offer, we explain the limits before the finish is designed. A front that seals openings or does not match the listing is not fitted.
Roof penetrations and the roof covering
A vertical vent route ends with a penetration through the roof. The flashing must suit the roof covering, and the vent instructions call for a storm collar sealed to the pipe above it. Roof coverings differ, and some need a roofer's work around the flashing.
We plan the roof exit with the covering in mind and agree who does what. We fit the vent, flashing and storm collar as the instructions show. If the roof covering around the flashing needs work beyond that, a roofer carries it out and it appears as their item on the estimate.
Items in a gas fireplace installation
- Vent system chosen from the manual
- Termination position against listed clearances
- Framing and chase layout to the manual
- Control and service access planned
New gas unit questions for Coral Ridge homes
Who arranges the appliance shutoff valve for a new fireplace?
The gas contractor fits the shutoff valve as part of the supply work, or it is arranged with the utility. We agree its position with them so it stays reachable after the finish. On vented decorative units it may be a remote valve that is permanently identified.
Can you install a propane fireplace?
Yes, where the model is supplied for propane or converted as its manual allows. Your propane supplier or a gas contractor handles the tank, regulator and piping. We confirm the fuel on the rating plate before the unit is set in place.
Is a decorative gas fireplace different from a heater-rated one?
Yes. Vented decorative fireplaces are listed to ANSI Z21.50, while vented fireplace heaters are listed to ANSI Z21.88. If warmth matters as much as the look, we point you toward heater-rated models during selection.
More Ways to Care for Your Fireplace
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Smoke Chamber RepairRepair identified smoke-chamber surfaces with the access and material requirements clearly defined.
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo