Built-in gas fireplace installation in Hialeah Gardens
Framing, firestops and vent clearances are built as the listing requires, then covered by your finish.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Projects that start with a gas fireplace plan
- Propane supply but no appliance yet
- A builder asking for framing details
- Several trades working on one room
- An old decorative unit that gives little heat
Jump to
What a gas fireplace installation involves
Replacing an existing gas fireplace
When an old gas fireplace fails or its parts become unavailable, a replacement is a new installation in an existing space. The new model's requirements are checked against the framing, vent and supply that are already there, and nothing is assumed to fit because the old unit did.
We identify the old unit and vent, then compare them with the manual for the model you are considering. Sometimes the opening and route suit the new unit with changes. Sometimes a different model fits better. You see the options and their implications before anything is ordered.
A wood fireplace opening is a different project
If the plan is to put a gas appliance into an existing wood fireplace opening, that is an insert or a log set rather than a built-in gas fireplace. Those projects use the existing chimney, which the fuel gas code says must be examined, and cleaned if it served solid fuel, before a gas appliance is connected.
We handle inserts and log sets under their own services, with their own planning. This installation service covers new vented gas fireplaces framed into a wall or chase. Tell us which you have in mind, and we point you to the right starting place.
Clearances to combustibles inside the framing
Inside the wall or chase, the appliance and its vent need specified air spaces to framing and other combustibles. The manual gives the figures for each model and warns that insulation and other materials must be secured so they cannot drift into those spaces.
We frame, or check the framing, against those clearances before insulation goes in. Spacers, standoffs and shields supplied with the appliance are fitted as shown. Once the wall is closed, those spaces cannot be seen, which is why they are checked and noted on your written record beforehand.
Closing an old vent or opening properly
When a gas fireplace moves or is replaced by a model with a different route, the old vent and termination may no longer be needed. They should be taken out or closed off properly so they do not let water or air into the house.
We explain what should happen to the old parts and which trade handles the wall, roof or finish repair. Our part of that work is priced on the estimate. Leaving an unused termination in place without sealing it is not part of a finished job.
Items in a gas fireplace installation
- Model selection against the room and route
- Fuel type matched to the house supply
- Framing and chase layout to the manual
- Supply handover point agreed with the gas contractor
What people ask about new gas fireplaces
Is it possible to raise a gas fireplace above floor level?
Some models allow a raised installation, provided the unit is supported by framing and the ceiling clearances in the manual are still met at that height. We check both during the project inspection, before any framing is built around the unit.
Do I need an electrician for a gas fireplace installation?
Often, because many models need household power for ignition, a blower or lighting. The manual states the requirement. If a new circuit is needed, an electrician installs it, and we coordinate the timing with the appliance work.
How do you handle framing and finishes around the unit?
We follow the framing and clearance drawings in the manual for the chosen model. Where a builder or another trade frames the chase or applies the finish, we share those requirements with them before they start.
More Ways to Care for Your Fireplace
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Chimney Animal RemovalAssess occupied chimney openings and plan appropriate follow-up cleaning or entry protection.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo