Direct-vent and B-vent gas fireplace installation in Idlewyld
Book the approved installation within 72 hours of your free inspection and save 10%.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Situations that lead to a new gas unit
- Planning a fireplace for a room without one
- Unsure where a vent could exit
- A unit bought before the route was checked
- A builder asking for framing details
Jump to
Choosing, framing and venting a gas unit
The listing printed on the rating plate
The Florida fuel gas code expects gas appliances to be listed and labeled for the application in which they are used. For a fireplace, the rating plate and manual tell you what the unit is listed as and how it must be installed.
We read the listing before the design is fixed. It decides the vent systems the unit accepts, the clearances it needs and the rooms it may go in. An appliance installed outside its listing can lose that protection, so the listing guides every later decision on the project.
Blowers and accessories from the approved list
Blowers, lighting kits, fronts and remotes are offered by manufacturers as accessories for specific models. They are part of how the unit was listed, and the manual names which accessories may be used with it.
If you want a blower or another option, we choose it from that list and plan its power supply and access. Adding an accessory later is often possible, but planning it now avoids opening finished walls. Anything not on the manufacturer's list for your model stays off the installation.
Leaving room for later decks and additions
A termination that meets every clearance on installation day can fall out of compliance later, when a deck, fence, shed or addition is built nearby. One owner's manual lists termination clearance to later construction among the owner's routine checks.
Tell us about projects you are planning outside, even if they are years away. We place the termination where future plans are least likely to crowd it, and we note the clearances on your record. Anyone designing later work around the house can then see what the termination needs.
Instructions on the job site at inspection
The Florida fuel gas code expects the manufacturer's installation instructions to be on the job site at the time of inspection. It also says that where the listing or the instructions are stricter than the code, they apply.
We keep the manual with the appliance throughout the work and follow it line by line. If a local requirement or an inspector asks for something beyond the manual, we discuss it with you and adjust the plan. The manual stays with the house when the job is finished.
What a gas fireplace project in Idlewyld includes
- Vent system chosen from the manual
- Control and service access planned
- Wall or roof penetration sealed
- Restrictor set for the vent configuration
Common questions on gas fireplace installs
Can you replace my old gas fireplace with a new model?
Yes, as a planned installation. The new model's requirements are checked against the existing framing, vent and supply. Old vent parts stay only where the new manual lists them for that appliance.
Can a gas fireplace share a vent with another appliance?
The manuals we work from call for a separate vent and prohibit venting into a pipe that serves a solid-fuel appliance. We plan a dedicated vent for the new unit as its manual specifies.
Should the fireplace go in before or after the finish work?
The appliance, framing and vent come first, and the finish follows to the manual's requirements. Some models allow certain finish materials only in set zones. We agree the sequence with your builder so nothing has to be undone.
More Ways to Care for Your Fireplace
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Chimney Cap Installation and ReplacementProtect the chimney opening with a cap chosen for its fit, attachment and compatible system.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo