New vented gas fireplaces installed in Miami Beach
A new gas fireplace in Miami Beach starts with a free project inspection and a written scope.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When a gas fireplace installation makes sense
- Planning a fireplace for a room without one
- Parts no longer made for the existing unit
- An old decorative unit that gives little heat
- Moving the fireplace to a different wall
Jump to
The parts of a gas fireplace project
Decorative listing or heater listing for the unit
Vented gas fireplaces come in two broad listings. Decorative units are listed to ANSI Z21.50 and are designed mainly for the look of the fire. Fireplace heaters are listed to ANSI Z21.88 and are designed to add heat to the room as well.
If warmth matters to you, say so during planning. We point you toward heater-rated models and explain what the manual says about their output and controls. If the look matters most, a decorative unit may suit. Either way, the listing on the rating plate settles which kind you are buying.
Choosing the wall for the fireplace
The wall you choose decides the vent route, the framing and the finish. Outside walls often allow short horizontal runs to a termination. Interior walls may need a vertical run through the ceiling and roof, or a longer path that the vent tables may not allow.
During the project inspection we look at each candidate wall in turn. We check what is inside it, where the vent could go and what the termination would sit near. You then choose with a clear picture of what each position involves, rather than finding out after the wall is opened.
Vent tables decide the route
Every direct-vent gas fireplace manual includes vent tables. They set how far the vent may rise and run, how many elbows it may use and where it may end. Diagonal runs count toward both the vertical and the horizontal limits.
We draw the planned route against those tables before framing starts. If it fits, the route is recorded for the builder. If it does not, we look for a different path or position rather than stretching the rules. A route outside the tables can affect how the appliance lights and burns.
Reusing an existing chase or enclosure
An existing chase or built-in enclosure can sometimes take a new gas fireplace, but its framing sizes, clearances, blocking and insulation must suit the new model. A chase built for one unit is not automatically right for another.
We compare the existing enclosure with the new manual during the project inspection. If changes are needed, they are listed and priced. If the enclosure cannot be adapted safely, we say so and explain what rebuilding it would involve, so you can decide before ordering.
The installation checklist for your gas unit
- Fuel type matched to the house supply
- Framing and chase layout to the manual
- Clearances to combustibles marked out
- Restrictor set for the vent configuration
Questions from Miami Beach about new gas fireplaces
Does the installation include the barrier screen and glass?
Yes. The barrier screen and glass assembly supplied with the unit are fitted as the manual shows. They are part of the appliance rather than optional trim, and the unit is not handed over without them.
Should the fireplace go in before or after the finish work?
The appliance, framing and vent come first, and the finish follows to the manual's requirements. Some models allow certain finish materials only in set zones. We agree the sequence with your builder so nothing has to be undone.
What if I smell gas after the new fireplace is installed?
Get everyone out of the house, leaving switches and the fireplace controls untouched. From the yard or the street, ring 911 or the gas utility, and stay out until they confirm the building is safe.
More Ways to Care for Your Fireplace
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Smoke Chamber RepairRepair identified smoke-chamber surfaces with the access and material requirements clearly defined.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo