New vented gas fireplaces installed in Pembroke Pines
Tell us where you want the fire, and we check whether a vent route and enclosure can support it.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When a gas fireplace installation makes sense
- Planning a fireplace for a room without one
- Parts no longer made for the existing unit
- An existing vent of unknown make
- Several trades working on one room
Jump to
Building a gas fireplace around its manual
Replacing an existing gas fireplace
When an old gas fireplace fails or its parts become unavailable, a replacement is a new installation in an existing space. The new model's requirements are checked against the framing, vent and supply that are already there, and nothing is assumed to fit because the old unit did.
We identify the old unit and vent, then compare them with the manual for the model you are considering. Sometimes the opening and route suit the new unit with changes. Sometimes a different model fits better. You see the options and their implications before anything is ordered.
The gas contractor's part of the project
Supply piping to a new gas fireplace is installed by a gas contractor, or arranged with the gas utility where they provide it. Their work covers sizing and running the supply, testing it and fitting the shutoff valve. We do not install supply piping.
We give the gas contractor the appliance position, the connection point and the input shown in the manual. Their work usually happens during rough-in, before walls close. Once the supply is ready and tested, we set and connect the appliance as the manual shows and carry out the leak and pressure checks at the unit.
Supply pressure tests and the appliance
When supply piping is pressure tested, the appliance must be protected. One manual requires the appliance and its valve to be disconnected from the supply during tests above a set pressure, or isolated by closing its shutoff valve during lower-pressure tests.
We agree the order of work with the gas contractor, so their test happens before the appliance is connected, or with the appliance isolated as the manual requires. That avoids damage to the appliance valve before the fireplace has ever been lit. The sequence is noted on the record.
Planning maintenance from the first season
Manufacturers ask for a new gas fireplace to be inspected and serviced by a qualified service person, and their manuals list what that visit covers. Planning for it from the start keeps the warranty conditions and the appliance in good order.
We can schedule maintenance visits that follow your model's list. Each visit builds on the installation record, so changes are easier to spot. Maintenance is optional and priced separately from the installation, and you decide when and whether to book it.
What your gas fireplace installation estimate covers
- Model selection against the room and route
- Shutoff valve position coordinated
- Appliance set, leveled and secured
- Pressure readings and operating check
What people ask about new gas fireplaces
Is it possible to raise a gas fireplace above floor level?
Some models allow a raised installation, provided the unit is supported by framing and the ceiling clearances in the manual are still met at that height. We check both during the project inspection, before any framing is built around the unit.
Does a direct-vent unit need a chimney?
No. A direct-vent gas fireplace uses a sealed vent system that draws outside air and exhausts through a listed termination on a wall or roof. The route and termination must fit the manual's rules for that model.
What stays with me after the installation is finished?
The installation and owner's manuals, a walkthrough of normal operation and a written record of the work listing the model, vent parts and checks. Keep them together near the fireplace or with your house papers.
More Ways to Care for Your Fireplace
- Fireplace RestorationCoordinate fireplace repairs while preserving suitable existing features and defining the intended use.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo