A gas fireplace for West Perrine, planned and installed
Framing, firestops and vent clearances are built as the listing requires, then covered by your finish.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Projects that start with a gas fireplace plan
- An existing vent of unknown make
- Several trades working on one room
- An old decorative unit that gives little heat
- Controls you would like to update
Jump to
Installing vented gas fireplaces in West Perrine
The gas contractor's part of the project
Supply piping to a new gas fireplace is installed by a gas contractor, or arranged with the gas utility where they provide it. Their work covers sizing and running the supply, testing it and fitting the shutoff valve. We do not install supply piping.
We give the gas contractor the appliance position, the connection point and the input shown in the manual. Their work usually happens during rough-in, before walls close. Once the supply is ready and tested, we set and connect the appliance as the manual shows and carry out the leak and pressure checks at the unit.
Comparing models on their requirements
Showrooms and websites show how a fireplace looks. The manual shows what it needs. When you compare models, look at the listing, the vent options, the framing and clearance requirements, the controls and the service access, as well as the appearance.
We help you compare the models you are considering on those points. We do not push a brand. If two models look similar but one fits your route and room far more easily, we say so. The final choice is yours, made with the requirements in view.
Reusing an existing chase or enclosure
An existing chase or built-in enclosure can sometimes take a new gas fireplace, but its framing sizes, clearances, blocking and insulation must suit the new model. A chase built for one unit is not automatically right for another.
We compare the existing enclosure with the new manual during the project inspection. If changes are needed, they are listed and priced. If the enclosure cannot be adapted safely, we say so and explain what rebuilding it would involve, so you can decide before ordering.
Break-in fires on a new gas unit
New gas fireplaces go through a break-in period described in their manuals. Paint and oils from manufacturing cure during the first hours of use, which can release an odor and leave a film on the glass. Some manuals ask for open windows and a glass cleaning after the first long burn.
We explain your model's break-in steps during the handover. A curing smell during those first fires is expected, and smoke detectors may react to it. If anything seems different from the manual's description, tell us and we will check it.
The installation checklist for your gas unit
- Framing and chase layout to the manual
- Attic insulation shield where the route needs one
- Control and service access planned
- Existing unit and vent assessed for replacements
Planning questions for a gas fireplace in West Perrine
Does a direct-vent unit need a chimney?
No. A direct-vent gas fireplace uses a sealed vent system that draws outside air and exhausts through a listed termination on a wall or roof. The route and termination must fit the manual's rules for that model.
Can the fireplace go on an interior wall?
Sometimes. The vent route has to reach a permitted termination within the vent tables for the model. Longer routes and extra elbows can rule some positions out, so we check the route before you commit to that wall.
Do you keep the manual on site for a code inspection?
Yes. The Florida fuel gas code expects the installation instructions to be available on the job site when the installation is inspected. We keep them with the unit during the work and hand them to you at the end.
More Ways to Care for Your Fireplace
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Fireplace RestorationCoordinate fireplace repairs while preserving suitable existing features and defining the intended use.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo