Gas fireplace venting for homes in Boca Del Mar
Termination caps replaced to the vent maker's listing and set to the manual's clearances.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Clues that point to the gas vent
- Nest or leaves at the outside cap
- Visible gap at a pipe joint
- Cap loose or missing after strong wind
- Heat marks on framing near the pipe
Jump to
The vent behind your gas fireplace
A joint that has pulled apart
Vent sections join with locking features designed for each system. If a joint was not fully engaged at installation, or has been disturbed during other work, sections can separate, leaving a gap in the inner or outer pipe.
A separated joint is a reason to leave the fireplace off. We trace the route to find the joint, which may be exposed or concealed. Once it can be reached, the sections are reassembled and locked as the instructions show, or replaced where they are damaged. Access and restoration are listed separately from the joint repair.
Leaks at a roof penetration
A vertical gas vent passes through the roof with flashing and a storm collar. One vent maker calls for a ring of nonhardening high-temperature sealant, such as silicone, around the pipe at the top of the storm collar to keep the roof watertight.
A ceiling stain near a vertical vent can mean the collar, sealant or flashing has failed. We check them where the roof can be reached safely and explain what we find. Vent-side repairs are quoted by us. If the roof covering around the flashing needs work, a roofer handles it.
Nothing fitted that slows the vent gases
The fuel gas code prohibits devices that retard the flow of vent gases in a vent, chimney or vent connector. Listed draft regulators, safety controls and certain approved devices installed to their instructions are the exceptions.
Screens added to stop pests, restrictors from another product or homemade caps can all slow the gases. If we find one, we explain what it is and why it should come out. The listed part the system needs, such as a proper termination cap, is quoted as the replacement.
Bracing a tall vent above the roof
A gas vent that stands well above the roof can move in the wind, stressing its joints and the flashing below. One vent maker asks for tall vents to be securely braced and warns against attaching the bracing to the cap.
We check whether a tall roof termination is braced as its instructions require and whether the bracing is attached to the pipe rather than the cap. Missing or failed bracing is replaced with the parts the vent maker lists. The roof seal is checked at the same time, because movement often shows there first.
Gas vent parts and checks for Boca Del Mar homes
- Restrictor setting against the route
- Separate vent confirmed for the appliance
- Written record of the vent work
- Decorative shroud listing confirmed
Before you book gas vent work
Can you replace just the termination cap?
Yes, if the rest of the system is sound and the cap listed for your vent system is available. We confirm the vent maker and system from the labels before ordering, and check the joints nearest the cap while we are there.
What is a draft check on a natural-draft fireplace?
After warm-up, a test at the draft hood relief opening shows which way the exhaust is moving, up the vent or back out into the room. We carry it out during vent work on draft-hood appliances.
Can you work on a power vent fitted to a gas fireplace?
Where the power vent is listed for the appliance, we can assess it and follow its manual. That manual calls for the venting to be safety-checked before and after any installation work. Its household circuit stays with an electrician.
More Ways to Care for Your Fireplace
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo