Gas fireplace vent repair and replacement in Wynwood
Draft problems on natural-draft units are checked at the draft hood and traced to their cause.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Outside and inside signs of gas vent trouble
- Termination cap bent or crushed
- Plants grown over the termination
- Vent pipe loose where it meets the wall
- Unknown vent parts after a renovation
Jump to
Gas vent pipes, joints and terminations
A joint that has pulled apart
Vent sections join with locking features designed for each system. If a joint was not fully engaged at installation, or has been disturbed during other work, sections can separate, leaving a gap in the inner or outer pipe.
A separated joint is a reason to leave the fireplace off. We trace the route to find the joint, which may be exposed or concealed. Once it can be reached, the sections are reassembled and locked as the instructions show, or replaced where they are damaged. Access and restoration are listed separately from the joint repair.
Wind, downdrafts and the vent cap
One vent maker explains that a cap resists rain, debris and birds and limits the effect of wind on the vent, including downdrafts from wind striking it directly. The same maker adds that no cap can overcome a zone of high pressure around the termination or low pressure inside the house.
If your fireplace behaves badly only in certain winds, mention the pattern. We check the cap and the termination position against the manual's rules. Where the position itself sits in a poor spot, we explain the options, including relocating the termination within the vent tables.
Vent-free units have no vent to repair
A vent-free gas fireplace or log set does not use a vent. Its combustion products stay in the room, and its listing depends on protective devices and limits on room size.
If your appliance is vent-free, this venting service does not apply. It is handled under our ventless gas fireplace service, which follows the requirements for that design. If you are not sure whether your appliance is vented, the rating plate and manual will say, and we can check it for you.
Elbows added during a repair
Every elbow counts against the limits in the appliance's vent tables. A repair that adds an elbow to clear a new beam or duct can push a route that was within the tables outside them.
We count the elbows and offsets in the route before and after any change. If an added elbow would break the tables, we look for another way to route the section. Offsets and elbows used in the repair are listed on your record, so the next change starts from an accurate picture.
Checks and parts on your venting quote
- Concealed sections recorded as not seen
- Termination clearances against the manual
- Firestops and wall shields at crossings
- Access opening and restoration priced separately
Direct-vent and B-vent questions we hear
Do you check the vent connector on natural-draft units?
Yes. The connector joins a natural-draft appliance to its vent, and the fuel gas code requires noncombustible, corrosion-resistant material able to handle the vent gas temperature. We check its material, joints, slope, support and clearance, and quote a replacement where it fails.
Can you work on a power vent fitted to a gas fireplace?
Where the power vent is listed for the appliance, we can assess it and follow its manual. That manual calls for the venting to be safety-checked before and after any installation work. Its household circuit stays with an electrician.
What happens to the old vent parts you remove?
We take them away with the other debris, which is cleaned up and hauled away before we leave. If you would like to see or keep a damaged section, say so and we will set it aside for you.
More Ways to Care for Your Fireplace
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo