Stone chimneys in Boca West, reset and repointed with care
From one loose stone to a whole face, you approve the scope and price before we begin.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What loose chimney stone can look like
- A section of stone bulging outward
- Damp patches that linger on the stone
- A dark band that stays wet after rain
- Mortar that powders when scratched
Jump to
Our approach to stone chimney repair
Getting new joints to blend with old ones
New mortar is darker when wet and lightens as it cures. Judging a color match on the day it goes in can mislead. The sand in the mix drives most of the final color and texture.
Where joints will be visible, we prepare a small sample and judge it once it has dried. National Park Service guidance on repointing stresses matching color and texture as well as strength. You see the dried sample before the full repointing goes ahead, and you can ask for an adjustment.
Gentle cleaning for chimney stone
The manufactured stone installation guide advises against harsh chemicals such as raw acid, and against wire brushes or power washers, when cleaning adhered stone. National Park Service guidance on masonry cleaning favors the gentlest method that does the job.
We start with water and soft brushes and step up only if needed, testing first in an inconspicuous spot. Cleaning appears on the estimate when the repair needs it, not as a cosmetic extra added to the bill. If a stain will not shift safely, we tell you rather than force it.
Patches that stay dark long after rain
Stone darkens when wet and lightens as it dries. A patch that stays dark long after the rest has dried is holding water, often because water keeps feeding it from behind or above. Noting the pattern on a dry day after rain gives us a useful map.
Note where those patches sit and tell us when you call. We compare them with the joints, the top and the drainage edge. That pattern often points to the repair more clearly than the stones themselves, and it helps us avoid repointing joints that were never the problem.
Using the fireplace during stone work
Exterior stone repair does not usually affect the fireplace. The stone sits on the outside of the chimney or its enclosure, away from the flue and the firebox. If the chimney serves a gas appliance, the same care applies to its vent opening.
If the work reaches the top, the flue area or the inside of a framed chase, we tell you whether to hold off using the fireplace until that part is complete. We also keep mortar, dust and debris away from the chimney opening while we work above it.
How we itemize stone chimney work
- Tooling joints once the mortar firms up
- Corroded ties noted and addressed
- Open areas covered at the close of each work day
- Written record of stones reset and replaced
What people ask about stone chimney repair
Why not just glue a loose stone back in place?
Adhesive is not a substitute for a proper mortar bed on an exterior wall. A glued stone can let go again, and the glue can block the drainage behind it. We reset stones the way the assembly was meant to hold them.
What if the backing behind the stone is damaged?
We stop and show you what we found. Backing repair, such as lath, scratch coat or framing work, is priced as its own item. The stone goes back once the surface behind it is sound again.
Do you cover open areas if the work takes more than a day?
Yes. Before we leave each day, any area where stones are off is sheltered from rain, and removed stones are stored safely until they go back. Loose debris goes with us rather than staying on the roof.
More Ways to Care for Your Fireplace
- Chimney WaterproofingTreat suitable chimney masonry after checking the surface, repair needs and product requirements.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo