Stone chimney repair in Colee Hammock matched to your stone
Upfront prices, a workmanship warranty and a written record come with every stone repair we carry out.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What loose chimney stone can look like
- Stones missing from the chimney face
- Damp patches that linger on the stone
- Stains inside near the fireplace wall
- Loose stones above a door or walkway
Jump to
Our approach to stone chimney repair
How a loose stone is reset
Resetting starts with cleaning. Old mortar comes off the back of the stone and off the surface it will sit on, so the new bed has something clean to grip. The setting surface is dampened as the mortar maker directs.
The stone goes back in a full bed of mortar and is pressed until mortar squeezes out at its edges. The joints are then filled and tooled to match. A stone set this way is held across its whole back, not at a few points. Instructions for one manufactured stone say a disturbed stone must come out, be cleaned and be set again rather than pushed back.
White deposits washing out of the joints
White deposits on stone or in the joints usually come from dissolved minerals carried by moving water. As the water evaporates, the minerals are left on the surface as a powdery film or a crust. Heavy or returning deposits suggest a steady water supply rather than a single soaking.
The deposits are a clue rather than the damage. We look above them for the route the water is taking, whether an open joint, the top or the flashing. Once the water is stopped, the deposits tend to fade, and gentle cleaning can remove what remains without harming the stone.
The weight a stone face places on its support
Stone is heavy. Natural stone veneer in particular adds weight that the wall, ties or backing must carry. Manufactured stone is lighter, but it still depends on a sound surface behind it. Adding more stone to a struggling backing only increases the load.
When we see stones pulling away along a line, we consider whether the support behind them is coping with the weight. That can decide whether we reset stones straight away or first repair what holds them. We explain that reasoning in plain terms and show where we saw the evidence.
Keeping joint widths consistent
Joint width is part of the look of a stone chimney. Repairs with joints noticeably wider or narrower than the rest stand out, even when the mortar color matches well. Joint depth is matched too, so shadows fall the same way across old and new.
We set replacement and reset stones to keep joints consistent with their surroundings. Where the original joints vary, as they often do with natural stone, we follow the pattern of that particular face rather than forcing a uniform grid onto it. The goal is a repair that reads as part of the original work.
Line items in a stone chimney estimate
- Raking deteriorated joints back to sound mortar
- Separate line for flashing work at the roof
- Open areas covered at the close of each work day
- Sealant joints at changes of material
What people ask about stone chimney repair
Is a stone veneer chimney repaired differently from a solid stone one?
Yes. Solid stone carries its own weight and relies on its joints. Veneer depends on a backing, ties or a mortar bed, and a drainage path behind it. The repair addresses whichever part has failed.
Why not just glue a loose stone back in place?
Adhesive is not a substitute for a proper mortar bed on an exterior wall. A glued stone can let go again, and the glue can block the drainage behind it. We reset stones the way the assembly was meant to hold them.
When is a hose water test used on a stone chimney?
Selectively, when the job calls for it, meaning the water route is still in doubt and the answer would change which joints or stones we repair. Many stone jobs never need one, and we explain what it would show first.
More Ways to Care for Your Fireplace
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo