Chimney stone repair for homes in Poinciana Park
From one loose stone to a whole face, you approve the scope and price before we begin.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What loose chimney stone can look like
- A stone that moves when touched
- Stones missing from the chimney face
- Rust streaks running down the stonework
- Caulk or foam from earlier quick fixes
Jump to
The thinking behind each stone repair
Mortar that gives way before the stone does
Repointing mortar should be softer and more vapor-permeable than the masonry around it. That is the central point of the National Park Service guidance on repointing. If the joint is harder than the stone, stress and moisture move into the stone instead.
Softer stones then crack or flake at their edges while the hard joint stays intact. We choose a mortar suited to the stone on your chimney, and the estimate describes it in plain words. Strength alone is not the goal, because a joint is meant to be the part that wears.
Gentle cleaning for chimney stone
The manufactured stone installation guide advises against harsh chemicals such as raw acid, and against wire brushes or power washers, when cleaning adhered stone. National Park Service guidance on masonry cleaning favors the gentlest method that does the job.
We start with water and soft brushes and step up only if needed, testing first in an inconspicuous spot. Cleaning appears on the estimate when the repair needs it, not as a cosmetic extra added to the bill. If a stain will not shift safely, we tell you rather than force it.
Stone adhered to block or concrete
Adhered stone can go directly onto clean block or concrete. The installation guide says those surfaces must be free of sealers, paint and form release agents, or lath is needed so the mortar has something to grip. Any coating found on the block is removed or covered with lath before stones go back.
When stones fall from a masonry surface, we check what that surface was like underneath. A painted or sealed wall may explain the failure. The repair then starts with preparing the surface properly, whether by cleaning it back or adding lath, before any stone is set again.
Deciding on the stone work after your inspection
After your free inspection, you have time to consider the estimate. Book the stone work within 72 hours of that inspection, and 10% comes off the service. The discount applies to whatever scope you approve. The window counts from your own inspection date, whenever that falls.
If you need longer, take it, because the window affects only the discount. The estimate, its line items and the reasoning behind them stay the same. Ask us to go through any item again before you decide, including the options you are unsure about.
How we itemize stone chimney work
- Raking deteriorated joints back to sound mortar
- Scratch coat or lath repair behind adhered veneer
- Hose water test when the job calls for it
- Sealant joints at changes of material
Common questions on stone repair
Do you cover open areas if the work takes more than a day?
Yes. Before we leave each day, any area where stones are off is sheltered from rain, and removed stones are stored safely until they go back. Loose debris goes with us rather than staying on the roof.
What mortar do you use for repointing stone?
One chosen for the stone and the assembly. For natural stone, the mortar should not be harder than the stone. Manufactured stone follows its maker's guidance. We explain the choice rather than using one mix everywhere.
Can you repair stone on a framed chimney chase?
Yes, while respecting what the stone hangs on. Stone on a framed chase relies on the sheathing, barrier and lath behind it. If the framing is damaged, that repair comes first as a separate item.
More Ways to Care for Your Fireplace
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Smoke Chamber RepairRepair identified smoke-chamber surfaces with the access and material requirements clearly defined.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo