Chimney cap installation on homes across Coral Ridge
Your free inspection covers the cap, the flue top and the surface it mounts on, explained in plain terms.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Cap faults we fix on chimneys in Coral Ridge
- No cap visible on the flue
- Scratching or chirping heard in the flue
- Nesting material showing at the top
- Cap shifted after a strong storm
Jump to
Chimney cap work for homes in Coral Ridge
A cap that did not match its flue
Some caps simply did not match their flue when they were fitted. A cap that is too small may perch on the tile with bolts at full stretch. One that is too large may lean, leave gaps at the corners or catch the wind.
We compare the existing cap with the flue it sits on and tell you whether the fit was ever right. If it was not, we measure properly and propose a cap that matches the flue. Tell us if the old cap came from a store and was fitted without measuring. That history often explains why it failed.
When the water appears is a clue
Notice when water shows up. Water in the firebox during a heavy downpour often means rain is coming down the flue or around its top. Water that appears a day later, or only when wind comes from one side, may be soaking through the masonry or the flashing instead.
Write down the date, the weather and where the water appeared. That record narrows the search before we even climb up. Share it when you arrange the free inspection. We then check the cap first where the timing points to the flue, and look elsewhere where it does not.
Caps on a maintenance visit
Caps benefit from a look now and then, even when nothing seems wrong. On a maintenance visit, we check the fasteners, the lid height, the screen for holes or clogging, and the tile or crown around the base. Small problems are easier to deal with before the cap comes loose.
If you book a maintenance visit for the fireplace or chimney, the cap is part of it. We note anything that needs attention and tell you whether it is urgent or can wait. Nothing is replaced during a maintenance visit without your approval first.
Flashing leaks are not cap problems
Flashing is the metal that seals the joint where the chimney passes through the roof. Water that enters there runs down the outside of the flue and shows up on ceilings, walls or in the fireplace. It can look like a cap problem from indoors.
We check the flashing when water is part of the complaint. If it is the source, we tell you, and flashing repair is quoted as its own job. A new cap would not change that leak. Knowing where the water really comes in saves you paying for a cap that was not the cause.
What a chimney cap proposal should name
- Flue count and position on the top
- Removal of the old cap and hardware
- Access for later sweeping and screen cleaning
- Debris cleared from the roof and hauled away
Your chimney cap questions, answered in Coral Ridge
Can you fit a cap on a factory-built metal chimney?
Yes, using the cap its maker lists for that chimney. The Florida Building Code requires factory-built chimneys to be terminated as the manufacturer's instructions say. If the chimney label is reachable safely from indoors, read it to us when you call.
Will you need to drill into my chimney crown?
Only for caps that mount on the crown. Their flanges are fastened into the crown and kept back from its edge so the concrete does not crack. Caps that clamp to a flue tile or band around the brick need no drilling there.
What happens if the flue tile is cracked under the cap?
A cap clamped to a cracked tile may not hold, and the crack can let water into the chimney. We list the damaged tile as its own line on the estimate so you can decide on that repair before the cap goes on.
More Ways to Care for Your Fireplace
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo