Taking a chimney down and rebuilding it in Bay Colony
Our family team plans the rebuild with your roofer, so the flashing and covering close properly.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When patching gives way to rebuilding
- Cracks running through several bricks
- Flue tiles showing through open joints
- A bulge in the chimney face
- Water pouring in around the chimney
Jump to
Rebuilding the stack with the flue in mind
Why a rebuilt stack keeps to its line
A masonry chimney may only step out from a wall so far, and its flue may only shift sideways so far as it rises. Florida's building code sets both limits. Those limits protect the stack's balance and the flue's path.
A rebuild follows the chimney's existing line unless there is a good reason to change it. We do not add projecting shapes or shift the stack in ways the code does not allow. If the old chimney had features that fall outside those rules, we explain how the rebuild would handle them.
Metal ties between the new stack and the house
Where a chimney runs alongside the house, it is often tied to the structure. The brick industry's chimney guidance describes corrosion-resistant metal ties between a single-width chimney and the building behind it.
When the rebuild reaches levels where ties belong, we check the existing ties and add or replace them as the courses rise. Rusted or missing ties can explain why a chimney pulled away in the first place. The estimate lists the tie work and the metal used, so it is not left out of sight.
When nearby roof sections affect the height
The height rule looks at more than the spot where the chimney passes through the roof. Higher parts of the building within a set distance of the chimney count too, such as a raised roof section or an addition built after the chimney.
A chimney that met the rule when it was built may not meet it after later changes to the house. We look at the roof around the chimney during the visit and explain whether the rebuilt top must be taller to satisfy the code. The estimate states the planned height in words.
Using the fireplace again after the rebuild
Once the new mortar and crown have cured, the fireplace can go back into use. We give you the date in the written record of the work, based on the materials used and the weather during the job.
If anything about the fireplace seems different afterwards, stop using it and tell us what you noticed. A new smell, a stain or smoke where you did not see it before are examples. If nothing changes, no further step is needed. The workmanship warranty and the written record cover the rebuilt section if a question comes up.
Line items in a chimney reconstruction
- Base flashing coordinated with the roofer
- Clearance to framing at roof and attic
- Roof covering protection
- Flue size kept to suit the fireplace
What people ask before a rebuild
What if you find more damage below the planned line?
We stop and show you what removal uncovered before going further. You hear what it means and what it would add, and the boundary moves only with your agreement.
Can the rebuild be split into stages?
Partly. Loose masonry can be made safe first and the rebuild scheduled later. Once removal starts, though, the section is usually rebuilt in one sequence, so the chimney is not left open.
Will a rebuild change how my fireplace draws?
It should not make it worse. The rebuilt flue is kept to a size that suits the fireplace, and the top follows the code's height rule. If draft was a problem before, we explain what the rebuild can and cannot change.
More Ways to Care for Your Fireplace
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
- Chimney Sweep and Chimney CleaningArrange careful chimney cleaning in Miami with a defined scope, protected work area and useful findings.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo