Rebuilding damaged chimneys in Rock Island
A rebuild starts with a clear removal boundary, agreed with you before any brick comes down.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Rebuild warning signs at homes in Rock Island
- Mortar washed out deep in the joints
- A crown broken into loose pieces
- A bulge in the chimney face
- Water pouring in around the chimney
Jump to
How a chimney rebuild comes together
Setting the line where removal stops
The removal line is where new work will meet old. It should sit in masonry that is sound: firm mortar, tight units and no cracks running down past it. Set too high, it leaves weak masonry under the new work. Set too low, it adds cost without need.
We set a planned line on the estimate, based on what we can test before removal. We then confirm it as the courses come down. You see where it sits and why, in words you can check against the chimney itself.
Where new lining meets the old
In a partial rebuild, the new flue lining must meet the lining that stays below. Code rules for clay linings expect them to run from the top of the smoke chamber, or from below the lowest inlet, to a point above the chimney's enclosing walls.
Where old and new tiles meet, the joint has to be sound and smooth on the inside. If the retained lining is damaged, a rebuild does not fix it by itself. We check the lining below the rebuild line where we can and tell you whether it needs its own repair.
A formed crown with an overhang
The brick industry's chimney guidance favors a precast crown or a cast-in-place crown shaped like one, with thickened edges and an overhang past the brick. The overhang keeps rain off the top courses and throws it clear of the face.
We describe the crown's form on the estimate: how it is made, how it sheds water and how it sits over the new masonry. Where a precast crown suits the chimney, we explain the choice. Either way, the finished crown is sloped, overhangs the brick and carries a drip edge.
Maintenance visits after a rebuild
A rebuilt chimney still benefits from a look now and then. A maintenance visit checks the crown, the cap, the flashing and the joints of the new courses, along with the masonry below the removal line.
Small things, such as a sealant joint at the flashing or debris on the crown, are easier to deal with early. You decide how often a visit suits your chimney. Any work found is priced separately, and there is no plan to join. Looking at the chimney from the ground after strong winds is a useful habit between visits.
Items in a rebuild above the roofline
- Clearance to framing at roof and attic
- Mortar chosen for chimney exposure
- Debris removal and haul-away
- Written record of the rebuilt section
Questions about chimney rebuilding
Does the rebuild include a new crown and cap?
A rebuilt top normally gets a new crown, sloped with a drip edge and a bond break around the flue lining. A rain cap is fitted or refitted to suit the flue, and both appear on the estimate.
What if you find more damage below the planned line?
We stop and show you what removal uncovered before going further. You hear what it means and what it would add, and the boundary moves only with your agreement.
Do I need an engineer before the chimney is rebuilt?
Only when the damage suggests a structural cause, such as a stack pulling away from the house, stepped cracking or signs the base has moved. We explain when that assessment should come first.
More Ways to Care for Your Fireplace
- Chimney WaterproofingTreat suitable chimney masonry after checking the surface, repair needs and product requirements.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo