New vented gas fireplaces installed in Brickell Key
Direct-vent or natural-draft, the vent system is matched to the appliance, not to the nearest pipe.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When a gas fireplace installation makes sense
- A renovation opening up the wall
- Wanting a fire without burning wood
- Propane supply but no appliance yet
- A builder asking for framing details
Jump to
Gas fireplace installation, from room to handover
Elbows, offsets and the length of the run
Each elbow in a vent run adds resistance, and manuals count elbows and offsets against the allowed length. Some manuals let a pair of angled elbows replace a single square turn, and they explain how to measure pipe by its effective length rather than its overall length.
We keep the route as simple as the room allows and count every fitting against the table. If an offset is needed to clear a beam or duct, we check its effect before framing around it. The final route and fittings list are written into the installation record.
Pressure readings and the operating check
Before handover, the appliance is commissioned as its manual describes. That usually includes inlet and manifold pressure readings, a check of the pilot and burner flames, and a look at ignition across the whole burner.
We record the readings and compare them with the manual's figures for your fuel. The unit is run through its controls, including remote, thermostat and blower where fitted. If a reading or behavior falls outside the manual, we find the cause before handover rather than leaving it for the first service visit.
Plants and landscaping near the termination
Shrubs, vines and trees can grow toward a wall termination, and leaves and debris can collect around it. One owner's manual lists plants, nests, leaves and debris among the things to check at the termination.
When choosing the exit point, we look at the planting around it and mention what will need trimming over time. After installation, keep growth clear of the termination as the manual describes. If landscaping plans are underway, share them so the termination and the garden do not end up competing for the same space.
Air returns and air handlers near the fireplace
The position of heating and cooling returns can affect a natural-draft fireplace. One manual advises keeping furnace and air conditioning return vents away from the immediate area of the fireplace. It also lists an unbalanced air handling system among the causes of negative pressure.
During the project inspection we note where returns and air handlers sit relative to the planned position. If a return sits close by, a direct-vent unit or another position may be the better choice. Changes to the air handling system are outside our scope and belong to that trade.
What your gas fireplace installation estimate covers
- Room and appliance position review
- Listing and manual confirmed for the model
- Termination position against listed clearances
- Leak check at the appliance connection
Questions from Brickell Key about new gas fireplaces
Can a gas fireplace go in a bedroom?
The fuel gas code limits gas appliances in bedrooms and bathrooms, with exceptions that include direct-vent units installed to their listing and manual. Whether your model qualifies depends on its listing, so we check that before planning the location.
Where can the vent termination go on an outside wall?
Only where the manual's clearance rules allow it, measured from openable windows and doors, soffits, corners, meters, decks and walkways. We mark the position during the project inspection, before any opening is cut.
Is a decorative gas fireplace different from a heater-rated one?
Yes. Vented decorative fireplaces are listed to ANSI Z21.50, while vented fireplace heaters are listed to ANSI Z21.88. If warmth matters as much as the look, we point you toward heater-rated models during selection.
More Ways to Care for Your Fireplace
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Smoke Chamber RepairRepair identified smoke-chamber surfaces with the access and material requirements clearly defined.
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo