Refractory panels and metal fireboxes repaired in Brickell Key
We haul away old panels and debris, and any chimney left open is covered before we finish each day.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Clues that a prefab chimney needs attention
- Rust flakes inside the firebox
- Chimney pipe joints pulled apart
- Louvers painted over or blocked
- No label or manual for the unit
Jump to
Inside a factory-built fireplace repair
Louvers and air passages that must stay open
Some factory-built units draw room air through louvers or grilles around the opening and let it out above. That air cools the outer body and, on circulating models, warms the room. Manuals ask for these passages to be kept clean and unobstructed.
Paint, a new facing or a decorative cover over the louvers can trap heat inside the unit. We check each grille and passage we can reach and look for anything built over them later. Clearing or restoring them follows the manual, and any change to the facing is listed separately.
Hard starts and a sluggish fire
A fire that will not catch, smolders or sizzles can point to wet wood, a damper that is not fully open, a restricted cap or a closed outside air control. Manuals list these first. They are simple to check before anything is taken apart.
We run through that list with you during the inspection. If the simple causes are ruled out, we look at joints, height and blockages in the chimney. You hear which cause we found and what it will take to correct, along with the parts involved.
Preparing the room for a prefab inspection
Stop using the fireplace the day before, so it is cool when we arrive. Leave the screen and any doors as they are, without taking parts out to look. Clear the hearth of decorations and the path to the attic hatch of stored items.
If pets use the room, plan somewhere else for them during the visit. We protect the floor near the fireplace before we start. When we finish, the room is left as we found it, minus any debris we removed.
Sealant only where the manual allows it
Manuals specify where sealant goes, such as between the outside air hood and the house wall, and which kind suits the heat. Caulk or foam in the wrong place can block air spaces or fail under heat.
We remove sealant that sits where it should not and replace it only as the manual describes. Foam packed around a chimney where it passes a ceiling is not a firestop. The listed firestop goes back in its place, and the foam comes out.
What we confirm before ordering prefab parts
- Maker's parts list for the model
- Warping or burn-through in the firebox
- Clearances to trim and facing
- Hearth extension and protective strips
Asked about zero clearance fireplaces in Brickell Key
Can chimney pipe from another brand go on my prefab fireplace?
Not unless the fireplace listing names it. The unit was tested with specific chimney parts, and the Florida Building Code asks for installation to that listing. Sections from different systems can look alike yet join differently, so we match the pipe to the label.
What do you check after a prefab fireplace has overheated?
Warped metal, glowing parts and loud cracking are signs manuals link to overfiring. We check the firebox metal, the refractory and the chimney joints for heat damage. Some damage is repairable with listed parts, and some means the unit should be replaced.
Could my wood-burning prefab unit take a gas appliance later?
Only if the fireplace listing allows it. The building code limits gas appliances in factory-built fireplaces to units tested and listed for that use. This service covers the wood-burning unit, so we note what the label says and point you to the right next step.
More Ways to Care for Your Fireplace
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo