Direct-vent and B-vent gas fireplace installation in Roosevelt Gardens
From selection to handover, a gas fireplace installation in Roosevelt Gardens with no hidden fees.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs it may be time for a new gas unit
- An existing vent of unknown make
- A builder asking for framing details
- Cabinetry planned around the fireplace
- An old decorative unit that gives little heat
Jump to
What a gas fireplace installation involves
The electrical supply the model needs
Many gas fireplaces need household power for the ignition module, a blower or lighting. The manual states the requirement, and some models call for a circuit that is not controlled by a wall switch. Others can run their controls on batteries.
We read the electrical requirement during planning and mark where the supply must arrive at the appliance. Where the position has no suitable circuit or outlet, an electrician provides one. We coordinate the timing, so the power is in place before the walls close and before the unit is commissioned.
Decorative caps and shrouds must be listed
You may want a decorative cover over a roof or wall termination. The manuals allow only listed decorative caps and shrouds used with the approved vent system, and one warns that a decorative cover can change the clearances the cap needs.
If you want a decorative cap, we choose it from the list for your vent system and check its clearances before ordering. A shroud made on site or taken from another product is not used. The chosen cap is recorded with the vent parts, so future service knows what is fitted.
Routing a vent through the attic
When a vent passes through an attic, it needs firestops at the ceiling, an attic insulation shield, support and the clearances the vent system specifies. Ducts, trusses and wiring in the attic can affect where the pipe can go.
We check the attic during the project inspection and plan the route around what is already there. Trusses are not cut to make room for the vent. The attic section of the route, including the shield position, is described on your installation record.
Break-in fires on a new gas unit
New gas fireplaces go through a break-in period described in their manuals. Paint and oils from manufacturing cure during the first hours of use, which can release an odor and leave a film on the glass. Some manuals ask for open windows and a glass cleaning after the first long burn.
We explain your model's break-in steps during the handover. A curing smell during those first fires is expected, and smoke detectors may react to it. If anything seems different from the manual's description, tell us and we will check it.
What we plan and install on a gas project
- Wall or roof penetration sealed
- Restrictor set for the vent configuration
- Leak check at the appliance connection
- Existing unit and vent assessed for replacements
Questions about installing a gas fireplace
Can you replace my old gas fireplace with a new model?
Yes, as a planned installation. The new model's requirements are checked against the existing framing, vent and supply. Old vent parts stay only where the new manual lists them for that appliance.
Is a decorative gas fireplace different from a heater-rated one?
Yes. Vented decorative fireplaces are listed to ANSI Z21.50, while vented fireplace heaters are listed to ANSI Z21.88. If warmth matters as much as the look, we point you toward heater-rated models during selection.
Is the installation covered by a warranty?
Our workmanship warranty covers the installation work we carry out. The appliance and vent parts carry their manufacturers' own warranties. We explain both on the estimate so you know which covers what.
More Ways to Care for Your Fireplace
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Stone Chimney RepairRepair affected stone chimney surfaces with the supporting construction and visual match considered together.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo