Gas fireplace venting for homes in Imperial Point
Termination caps replaced to the vent maker's listing and set to the manual's clearances.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs a gas fireplace vent needs attention
- A new deck built close to the vent
- Visible gap at a pipe joint
- Unknown vent parts after a renovation
- Pipe resting against attic insulation
Jump to
How we assess and repair gas vents
Water collecting at a wall termination
Some manuals ask for a horizontal termination cap to slant slightly downward so that moisture inside it can drain out. A cap set level or tilted back toward the house can hold water, which may run back along the pipe or into the wall.
We check the angle of the termination against the manual and look for staining on the wall and pipe below it. Where the cap or the last section was set wrongly, it is reset to the instructions. Any water damage to the wall behind is listed for the appropriate trade.
Water or air around the wall penetration
Around a vent that crosses an outside wall, the gap between pipe and wall must be permanently sealed with approved materials under the fuel gas code. That seal keeps combustion products from entering the building around the vent and also helps keep weather out.
Cracked or missing sealant, gaps behind the termination plate and stains on the inside wall are signs worth mentioning. We check the seal from outside and, where it can be reached, from inside. The penetration is resealed with the materials the vent instructions name, and damaged finishes are listed separately.
When the vent system is no longer made
Vent systems are sometimes discontinued, and replacement sections may become hard to find. Because the manuals prohibit mixing systems, a missing part cannot simply be swapped for a similar one from another maker.
If the original system is no longer available, we check the appliance manual for other approved vent systems. Where one is listed, the affected run may need replacing from the appliance to the termination with the new system. We explain the extent of that work before quoting it.
When a roofer joins the job
Roof terminations pass through the roof covering with flashing and a storm collar. Vent-side parts, such as the pipe, collar, sealant and cap, are within our work. The roof covering around the flashing may need a roofer, depending on the material and its condition.
We explain where our work ends and the roofer's begins before anything is started. If the roof around the vent has been leaking, the roofer may need to repair the covering after we renew the vent parts. The order is agreed in advance so the roof is not opened twice.
Items in a gas fireplace vent repair
- Blockage from nests, plants or debris
- Draft check at the draft hood
- Vent tables checked for any new route
- Decorative shroud listing confirmed
Direct-vent and B-vent questions we hear
Can a gas fireplace vent through an old masonry chimney?
Some appliances are listed to vent through a liner or gas vent inside a masonry chimney. Before the connection, the fuel gas code calls for the chimney passage to be checked for obstructions and cleaned if wood or another solid fuel was burned in it. Insert liners are handled under the insert service.
Do you need to open the wall to repair a vent?
Sometimes. The manuals do not require inspection openings at joints inside walls, so concealed sections may need an access opening. We explain the access needed, and the wall restoration is listed as its own item before you approve.
Is vent repair part of a gas fireplace service visit?
No. A service visit includes a look at the termination, but repairs to the vent are quoted under this venting service. That keeps appliance work and vent work clearly separated on the estimate.
More Ways to Care for Your Fireplace
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Chimney WaterproofingTreat suitable chimney masonry after checking the surface, repair needs and product requirements.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo